Enduro White Undercoat (water based) 5 GALLONS

** This item CAN be custom tinted. There is an extra $20 service charge for this which will be invoiced separately prior to shipping. In the comments of your order, please provide the Manufacturer of the original color and the color code.**

General Finishes Professional Enduro White Undercoat is similar to General Finishes Sanding Sealer with the addition of white colorant to provide a primer undercoat for white/off-white wood finishes. The high solids, heavy-bodied formula facilitates a fast film build and sands easily. Use as a basecoat for pigmented acrylic finishes. It dries tack-free in 10-20 minutes. Particularly effective on MDF.

General Finishes White Undercoat is a spray only product that can be applied over raw wood MDF, existing finishes and as an undercoat for White Poly and light-colored paints. It acts as a physical barrier rather than a chemical barrier. For woods that exhibit tannin bleed-through, we recommend General Finishes Stain Blocker. 

Enduro White Undercoat Application Steps 

1. Watch product overview video here.
2. Work in a well-ventilated area. 
3. Stir General Finishes Enduro White Undercoat thoroughly to reincorporate solids that have settled to the bottom of the can before and throughout the application process.
4. Test for adhesion over existing sealed surfaces. 
5. Thin as desired with distilled water; start with 5%, adding up to 10% by volume. 
6. Increase open time, if needed, with 10-15% by volume of General Finishes Extender, if allowed by local regulations. GF Extender will improve flow and leveling and increase open time, which is helpful in dry climates. 
7. Ready to spray from the container. Apply 1-2 coats, depending on the substrate, the amount applied, and the application method. If you apply 1 light coat you can sand through, add another coat. If you apply 1 solid first coat and sand lightly, then you only need one.If a faster build is desired over raw wood, use General Finishes Sanding Sealer for the first coat.
   • Spray application: Before spraying, strain through a medium-mesh filter. Spray wet films at 3-5-mil thickness. Medium air cap. Fluid tip sizes: Compressed air: .040, HVLP: .072 or Airless: .011-.013. medium air cap. Verify tip sizes with your equipment supplier. See our spray tip size recommendations here. Keep your gun at a 90° angle, 6-8" from the surface. On large, flat areas, use wet, even patterns 6-8" wide. For narrow surfaces, reduce the fan pattern to 2-3" wide to reduce overspray. Overlap each pass 25% to conceal lines. Wear a full filter (NIOSH/MSHA approved) respiratory & eye protection and work in a ventilated space. Read here for more information on spraying techniques.
   • Face frames on cabinets: Enduro professional products are engineered to be spray-only but can be applied successfully to cabinet face frames, edges or drawer fronts with a brush, staining pad or small cabinet specific 3/8" nap microfiber roller such as Whizz or AllPro brand. Larger areas may not level with hand application.
9. Dry time based on ideal conditions: 70°F/20°C; 50-70% humidity. Tack-free: 5-10 minutes. Ready to sand: 30-45 minutes. Re-coat: 1 hours. Inadequate dry time is one of the top reasons for product failure. You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a fine-grade (220-320) foam sanding pad. If in doubt, wait longer. Increase dry time if:Finish sand between coats with a fine-grade (220-320) foam sanding pad to improve smoothness and adhesion.
   • Humidity is over 80%
   • 3+ coats are applied
   • Thick coats are applied
   • Applying over an existing sealed finish
   • Layering General Finishes water- and oil-based products:
     • Water over oil: Let oil-based products dry 72+hr before applying water-based products
     • Oil over water: Let water-based products dry 24+hr before applying oil-based products
   • To accelerate dry time in humid conditions, add General Finishes Accelerator and work in a space with good ventilation and air movement. If you decide to re-coat before the recommended time, test dryness.
11. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.

Cure Time
Not applicable

Warning: Do not use water-based products with Linseed Oils or Danish Oils.